Drill Master 69652 Betriebsanleitung

REFERENCE MANUALDrillMasterGrain Drill Section Controller611327-11/10

Pre-Planting Seed Calibration Process (using CAL TEST function)This procedure is used prior to eld operation. These steps will determine a more accu

Pre-Planting Seed Calibration Process (using CAL TEST function)ContinuedCalibration Mode1. Turn Power toggle to ON and RUN/HOLD toggle to HOLD. Turn a

CrustBusterDrillMaster Quick Start Guide346-001150 Pg 12 Revised 11/2010Pre-Planting Seed Calibration Process (using CAL

CrustBusterDrillMaster Quick Start Guide346-001150 Pg 13 Revised 11/2010In-Field Operation in AUTO Mode1. Switch on trac

23Make sure your system is properly calibrated before beginning to apply product. We also recommend completion of Pre-Field System Checkout described

24SECTION ON/OFFThe Console has three Section On/Off toggle switches on top of the Console. The toggle switches turn Drill Sections ON and OFF directl

Operation (cont)General InformationWARNING DEVICEThe console is equipped with a RED warning light. In AUTO, the light will flash when the actual appl

26The AREA, DISTANCE and WEIGHT totals counters maintain a running count during operation regardless of the position of the rotary switch. When any o

27MAN HOLDCALHOLD3 When the desired counter number is displayed, press the “-” (RESET) button and LAr will be displayed. See Illustration to th

28TroubleshootingMessages / Warnings CALTypically indicates that defaults were entered by powering up with the CAL and “-” buttons held,

TABLE OF CONTENTSDescription of Operation, Safety and Care...3Installation...

29All DrillMaster consoles are tested prior to packaging, so unless there has been damage in shipment you can be confident that everything will be ope

30CONSOLEThe only way to field test a console is to con nect it to a harness on a vehicle with a known working console or install it on an E-POP (Elec

31CONSOLE INPUTSIf there is no response from any of the following tests, refer to the main wiring diagram to locate the next connector in line to ward

CrustBusterDrillMaster Quick Start Guide346-001150 Pg 23 Revised 11/2010Single Section System Diagram

CrustBusterDrillMaster Quick Start Guide346-001150 Pg 24 Revised 11/2010Multi-Section System Diagram

CrustBusterDrillMaster Quick Start Guide346-001150 Pg 25 Revised 11/2010

CrustBusterDrillMaster Quick Start Guide346-001150 Pg 26 Revised 11/2010

See the table below for SPEED CAL numbers to enter for various radar models or GPS speed sensors.Radars Cal No. Hz/MPHVansco .150 58.90Raven .148 59.8

CrustBusterDrillMaster Quick Start Guide346-001150 Pg 28 Revised 11/2010Description of Hydraulic CircuitOil from tractor

CrustBusterDrillMaster Quick Start Guide346-001150 Pg 29 Revised 11/2010Determining Hydraulic Motor RotationMotor rotati

The DrillMaster is designed to drive a Proportional Flow Control Valve using a PWM out-put. The valve controls the ow to 1 to 3 hydraulic

Tractor Hydraulic Requirements396-001160 SERVICEBULLETINHydraulicValvePush/PullBypassValveOpensorClosesDescription: The red handled

INSTRUCTIONS TO CALIBRATE FERTILIZER RATES ON HYDRAULIC DRIVE DRILL #1: Calibrate seed meter using standard calibration procedure. #2: Calculate ra

CrustBusterDrillMaster Quick Start Guide346-001150 Pg 32 Revised 11/2010Chart of Ratios for Fertilizer Sprockets4700 Dri

ROWS/SECTION: Enter the # of SEED METERS per section. For a twin row conguration, each twin row has 2 seed meters. This displays the rows per sect

Singulated Seed Planting with the DrillMasterSeed Meter Test Process (using CAL TEST function)This procedure is used prior to eld operation. These s

InstallationMounting the Display ConsoleSelect a mounting location which seems most workable, and that best ts your needs. It should be conven

ON/OFF SWITCH CONNECTIONThe DrillMaster system uses P/N 14360 power switch to turn the system on. If the P/N 14360 power switch is used, simply mount

DrillMaster Tractor Controller Wiring LayoutTo Run/Hold Switch (Gray Tie)To Astro 5 (Yellow Tie)(Controller to Hitch)To Battery10 Pin Harness on Drill

DrillMaster Console FunctionsThe DrillMaster features a large, easy-to-read liquid crystal display, easy-to-use rotary dial and lighted panel for nigh

DrillMaster Controller CalibrationInitial Setup Procedure1.Turn all section switches off and put system in hold.2. Press CAL for one (1) second to ent

Hydraulic Drive Meter Calibration NumbersThese are starting calibration values. They can be rened for your drill and seed using the Pre-Planting See